Legacy Turbo by Slajki

[zabrnek]

Mater bo lep

[klemz]

Tok lep, da ne bo več za Pokluko

[Psssiho]

Vesel sem da je šel v prave roke

[slajki]

Avto mi javi kode 11 in 42! Mogoce kdo ve kaj je narobe? Ter pri lepi voznji avto cuka...

[klemz]

11 Crank angle sensor or circuit

42 Idle switch or circuit

[pero999]

Smo tut gledal na internetu kaj je, sam nihče se ne znajde iz tega.

[klemz]

11 je senzor na odmični če se ne motm, 42 pa ventil prostga teka?

[cheno]

11 je senzor položaja glavne gredi
42 je stikalo za prosti tek, ki se nahaja v senzorju položaja lopute za gas oz. po domače potenciometru za gas.

slika TPS
http://www.surrealmirage.com/subaru/images/tps.jpg

navodila za testiraje TPS senzorja

Here's the procedure out of the chilton's manual to test the TPS switch.

1. Turn the ignition switch ON. 2. Measure the voltage between the ECU connector terminal and ground.

Voltage should be as follows:
Terminal 2 and ground: 0.7-1.6 volts with the throttle fully open
Terminal 2 and ground: 4.4-4.8 volts with the throttle fully closed
Terminal 3 and ground: 5 volts
Terminal 1 and ground: 0 volts

3. Ensure voltage smoothly decreases in response to throttle opening. If measurements are not within specification, check and repair ECU terminals or harness.

4. Disconnect the connector from the throttle sensor. Measure the resistance between throttle sensor terminals 2 and 3. Resistance should be 12 kilo-ohms.

5. Measure the resistance between terminals while slowly opening the throttle valve from the closed position.

Resistance should be as follows:
Terminals 2 and 4: 10-12 kilo-ohms with the throttle valve fully closed
Terminals 2 and 4: 3-5 kilo-ohms with the throttle valve fully open

6. Ensure resistance smoothly increases in response to throttle opening. If measurements are not within specification, replace the throttle sensor.

7. Disconnect connectors from ECU and throttle sensor.

8. Measure resistance between ECU connector and throttle sensor connectors.

Resistance should be as follows:
ECU terminal 1 and throttle sensor terminal 2: 0 ohms
ECU terminal 2 and throttle sensor terminal 4: 0 ohms
ECU terminal 3 and throttle sensor terminal 3: 0 ohms

9. Measure resistance between throttle sensor connectors and ground.

Resistance should be as follows:
Terminal 2 and ground: 1 mega-ohm minimum
Terminal 4 and ground: 1 mega-ohm minimum
Terminal 3 and ground: 1 mega-ohm minimum

[slajki]

Torej potrebujem samo motorček prostega teka, senzor glavne gredi je bil problem takoj po generalki. Ima mogoče kdo? Koliko stane nov?

[cheno]

koda 42 je za senzor položaja lopute za gas, v katerem je tudi stikalo ki sporoči ECU-ju, da uporablja motorček prostega teka za prosti tek(ko je gas na 0), ko dodajaš plin, motorček prostega teka ne deluje oz. ni potreben.

[slajki]

Zanima me katera glavca je menjala ALK-e na mojem legacyu? :-nzd

[cheno]

je kaj narobe z sileni ?

[slajki]

Na desnem kolesu je bil origial še v dokaj dobrem stanju. Na levem kolesu je bil en drug model ALK-ja(novejši, ampak čisto požrta guma), oba vijaka čez navoj pritegnjena(odvijal sem jih z meterskim rorom od začetka do konca)
Sedaj so gor ALK-ji od impreze STI 06.l. Pri vožnji je razlika očitna

[bojc T]

Jest nč

[picinni]

Sedaj so gor ALK-ji od impreze STI 06.l. Pri vožnji je razlika očitna

Me veseli